Large copper teakettle with rounded body, goose-neck spout and hinged handle having a medium arc, mounted on shaped flanges with three rivets. The domed lid has a small brass mushroom knob (replaced). Dovetailed seams on bottom and vertical seam on side opposite spout. Seamed repair to spout tip.
"F. STEINMAN" is stamped on the handle within a reserve.
Provenance
Transferred from Heritage Center Collection, Dec. 2012
Jack Brubaker, The Steinmans of Lancaster, pp. 11-15.
HJ Kauffman, Early American Copper, Tin & Brass, 1995, pp. 42-43.
HJ Kauffman, American Copper & Brass, 1979, p. 65.
Height (in)
13
Width (in)
16
Condition
Good
Condition Date
2013-11-13
Condition Notes
Many dents and overall wear. HJK says handle slightly shortened (likely done by him). Tip of spout replaced. Plugged hole in bottom. Replaced knob. Stamped name very worn. Tarnished with polish residue where the spout, handle, and lid meet the main body.
Object ID
G.77.14
Notes
When his father died in 1758, John Frederick Steinman, Sr. (1752-1823) moved with his mother to Lititz from his birthplace, Bethlehem, Pennsylvania. His mother remarried a few years later to John Christophe Heyne, a tinsmith and pewterer from Lancaster. The shop of Heyne and Steinman would become known as Steinman's Hardware Store, the oldest hardware store in America.
Place of Origin
Lancaster
Credit
Heritage Center Collection. Gift of Henry J. Kauffman
Copper teakettle with round body, gooseneck spout, very low domed lid w/ scrolled knob of sheet copper riveted onto lid with a hand-cut washer added under lid, suggesting repair or replacement. Curved handle hinges onto tapered plinth tab bases with two rivets each. Vertical dove-tailed side seam opposite single-seamed spout. Dove-tailed bottom.
Touchmark on top of handle is "R..REED." within a rectangular reserve with serrated ends.
Made by Robert Reed, working in Lancaster 1771-1779, then 1785-1795.
Provenance
Purchased by Heritage Center from Philip Bradley Antiques
Transferred from Heritage Center to LancasterHistory.org December, 2012.
Tax assessment lists Robert Reed 1786-1793.
Kauffman, Henry J. American Copper and Brass. New York: Bonanza, 1979.
Coppersmith info from Shelley Horvath Posten (dau. of Don Horvath), 2009
Copper dented and scratched overall, polish residue at handle hinges. Side handle break repaired with sheet iron patch secured to outside with two iron rivets. Knob appears to be a repair or a replacement.
Object ID
P.80.131
Place of Origin
Lancaster
Credit
Heritage Center Collection. Purchased through the generosity of the James Hale Steinman Foundation,
Strainer of glazed redware, but with a lighter brown color than most redware. Resting on three tapered 1-1/8 " long feet. The flat-bottomed dish has straight sides that flare out to a molded, high lip. Applied handles at sides. Large holes in bottom and three rows of smaller holes at sides.
Lead glaze overall with some streaks/runs of a darker brown.
Numerous chips on body overall; some large ones on underside and a large chip on the side; handle edges have suffered the most significant chipping loss. Glaze is crackled overall and has some staining, particularly on the interior. Feet are moderately worn.
Object ID
G.98.12.17
Place of Origin
Pennsylvania
Credit
Gift of Mrs. S.R. Slaymaker II, Heritage Center Collection
Saltcellar of Stiegel-type clear glass, blown into a 3-piece mold. Body is an inverted pear form on a pedestal base. Upper body decorated with 25 slightly slanted vertical ribs. Bottom is slightly concave with pontil mark at center.
Provenance
Donor bought cellar for $70.00 at Horst Auction on 10-19-96, from the collection of Edward Miller.
Small free-blown wine or dram glass, Stiegel type. Conical form. Low profile knop on stem. Round pedestal base with concentric ring created by folded foot. Pontil mark on bottom.
Provenance
Purchased by donor Hampton C. Randolph, Sr., for $65 at the sale of the Henry E. Balmer estate, Lancaster, PA on April 20, 1996, then donated to the Heritage Center of Lancaster County.
Clear, free-blown leaded glass mug, near barrel shape. Stiegel-type glass has bubbles and other imperfections throughout. Applied threading at rim; ribbed loop handle; engraved design on side is a bird with floral and foliate designs. Pontil mark on bottom has been smoothed around edges with grinding wheel.
Similar to #5, plate 35 in "American Glass" by George and Helen McKearin.
Provenance
Descent within the Nichols family of Lancaster Co. Family history states mug was always kept in a decorated dower chest, dated 1808.
Clear mold-blown Stiegel-type glass mug in cylindrical form. Bottom quarter has 14 fluted ribs that carry through to the bottom and converge on the pontil mark. Rim edged with gold. Side has multicolored fruit and floral paint decoration with a central orange oval cartouche outlined in gold with gold cursive lettering: "Remember me." Applied handle.
Provenance
Descent to Sarah Muench from family, likely her Aunt Alice Potter Fordney, an antiques dealer.
British quart-size pewter tankard, part of the Warwick Congregation's (now known as the Brickerville United Lutheran Church) communion service.
Straight-sided body with raised band below center; molded base. Hinged domed lid with erect thumbpiece and C-scroll handle. Applied to front of tankard is a cast decorated portrait medallion with the profiles of a man and a woman facing each other with a crown above their heads. Encircling the pair are the words: "LONG LIVE PRINCE AND PRINCESS OF ORANGE". The medallion commemorates the Prince of Orange (William III) and his wife Mary Stuart, daughter of Charles I of England. The couple ruled England as joint sovereigns 1689-1702.
Provenance
The entire communion service remained in use over the years until the congregation decided in 1997 to find a safe place for this valuable communion set. Purchased by the Heritage Center of Lancaster County.
Diameter of bottom is listed. Diameter of top is 4".
Condition
Good
Condition Date
2014-08-28
Condition Notes
Overall abrasions and staining. Cracked where handle is attached at top. Inside pitting. Some cracks on inside of lid's rim. Large dent above medallion.
Object ID
P.97.08.4
Place of Origin
England
Credit
Acquired through the generosity of the James Hale Steinman Foundation and Friends of the Heritage Center Museum, Heritage Center Collection
Pewter basin, part of the Warwick Congregation's (now known as the Brickerville United Lutheran Church) communion service.
High, rounded sides flare out to a flattened rim with rolled edge. Booge appears to be unhammered. Barns struck his large circular mark with an eagle on the inside of bottom. The left portion of the eagle as well as the letters "BAR" on the bottom are discernible, as well as the "HE" above the eagle.
Probably made in Middletown or Wallingford, Connecticut.
Provenance
The entire communion service remained in use over the years until the congregation decided in 1997 to find a safe place for this valuable communion set. Purchased by the Heritage Center of Lancaster County.
Pewter plate, part of the Warwick Congregation's (now known as the Brickerville United Lutheran Church) communion service.
Flat bottom, rounded booge and wide, flat rim with single reeded edge.
Underside struck with two oval marks: one has "Townsend and Compton" and the other reads "LONDON." Following are four small square marks in a row. The last one has the initials "T&C".
Provenance
The entire communion service remained in use over the years until the congregation decided in 1997 to find a safe place for this valuable communion set. Purchased by the Heritage Center of Lancaster County.
Clock wheel cutting machine used by Lancaster clockmaker Martin Shreiner, Sr. Made of steel and brass with turned wood handle knob on crank. Main frame of tool is steel resting on four rounded, downward-curving legs with coin-shaped feet. Many moving parts, arms and cranks/screws, including the swiveling cutting yoke/frame at top (cutter blade with arbor/spindle missing) and the shaped index arm that "reads" the holes on the 13"-diameter brass wheel furnished with concentric circles of surface holes.
The LaFonds call this a very sophisticated machine, incorporating Swiss, German and English ideas/influences. This indicates to them that the machine was made in America, very likely by Shreiner himself. It was imperative for clockmakers to own this tool to practice their trade. Few survive. This machine was first described in the early book or article (LCHS Bulletin) printed in 1917(or 1919) & 1939 by D. McGee who wrote about Lancaster clockmaking. Ed believes this machine to be "the finest American engine in existence" and that it very well may have been made by Shreiner, probably in the 1790s. The cutter blade was used to cut the teeth on the large brass wheels that turn the pinions. There would have been either a slitting cutter or a form cutter used. Carter Harris says form cutters were used by the 1790s.
Attributed to Martin Shreiner (1769-1866).
An 8x10 B&W photo is in picture file under "clocks." Also slide is in slide collection, #14-3-11.
Lancaster Borough, most likely
Provenance
Owned by two brothers, Samuel K. and William L. Fraser, clockmakers who lived in Lincoln (just west of Ephrata) and grandsons of clockmaker William Fraser (1801-1877), then to early collector Earl T. Strickler (FNAWCC) who had it on display at the Columbia Clock and Watch Museum. Upon Strickler's sudden death circa 1974, it was sold by his widow, Mary Jane Strickler, to Edward F., Jr. and Virginia A. LaFond who removed rust and kept it on a window sill. They then traded it to dealer Jamie Price for some clocks. Price had it on sale at the 2004 Philadelphia Antiques Show in mid-April where, as representative for the von Hess Foundation, Tom Cook, purchased it for this museum's collections.
Ed LaFond believes the Fraser family was related to the Gorgas family, thus they were in a position to inherit tools. Due to this, it was believed at first that both the machine and the scribe were from the Gorgas family. However, LaFond believes the Frasers were also related to the Shreiners. Stacy Wood claims this machine was one of Martin Shreiner's tools (Vol. 96, LCHS Journal).
Pitting on steel surfaces, slight discoloration on brass parts, signs of wear overall.
Object ID
G.04.19.1
Notes
Information from: Clockmakers of Lanc. Co., Wood/Kramer, 1977, p. 142. 225 Years of Timepieces (Catalog of 1st Annual Exh. of NAWCCM, 1979), p. 63. Stacy Wood researched origins and provenance of these tools and wrote article in Vol. 96 #4 of LCHS Journal. Conversations with Virginia LaFond ( 5/19/04), Ed LaFond (7/6/04) and Carter Harris (7/7/04).
Place of Origin
Lancaster
Usage
Shreiner, Martin
Credit
Gift of the Richard C. von Hess Foundation, Heritage Center Collection