Dovetail construction, wire nails used on interior. Inside is a till and a sliding drawer; shoe molding on all bottom inside corners. Below mid-line molding are two thumbnail-molded, side-by-side drawers with nailed joints and fitted with locks, escutcheons and bail-type brasses in batwing style.
Lid is two joined boards with ends tenoned into end boards and pegged, cutting board fashion. Edge molding is intrinsic, not applied, except for light molding attached to underside to create lip. Lid has strap hinges with fishtail terminals and is fitted with a lock and brass batwing-type escutcheon. Medallion is relief-carved into center of lid top with "18 SF 40." The meaning of this 1840 date is a mystery.
Molding at the base of chest; four ogee bracket feet.
Provenance
Provenance: One of twelve pieces of furniture transferred to this museum from the Lancaster County Historical Society. These pieces were part of the estate of Sarah Ann Stauffer (1913-1996) whose property, Lime Kiln Farm, was bequeathed to LCHS upon her death in 1996.
Clarke Hess had suggested the chest may have been made for Sarah Ann Frantz and the 1840 date may be her birth year. Often, he says, pieces of furniture were made for a child or heir at the time of the settling of an estate.
Research: Sarah Ann Frantz (sister of Sarah A. Stauffer's gr-grandfather Henry L. Frantz) was born 1835, Grandfather Samuel O. Frantz was born 1861, so this theory is incorrect. (The East Hempfield Twp. farm of Sarah A. Frantz is located on both the 1875 and 1899 Atlases, SW of Rohrerstown and S.O. Frantz is shown nearby on 1899 Atlas.)
Top has large crack through center and many dents, scratches and score marks. Loss at right end of mid--line molding of front. Multiple cracks in sides. Repairs done to feet. Refinished with heavy stain and varnish on lid and all interior surfaces. Original finish on front is heavily alligatored; finish on sides is crackled. Interior surfaces have had paper and textiles adhere to wet varnish. Sliding drawer has crack in bottom.
Object ID
G.99.41.9
Place of Origin
Lancaster
Credit
Transferred from Lancaster Co. Historical Soc., Heritage Center Collection
Button-hole cutter, creaser or marking tool is silver plated ferrous metal.
In form of a miniature spoon with a blade instead of a bowl. Blade is eye-shaped with raised midline extending from tip to tip. Edges of blade are fairly sharp. Handle end has the bust of a crowned femal monarch with long flowing hair and necklace above a decorative base of scrolls surrounding a cabochon. Shaft of tool is similar to an architectural column. Entire handle is made of two identical halves, cast and joined with side seams visible.
Provenance
Collected by Lillian Hollings Kiker, born to Scottish Americans who lived in New Jersey. Born (1912) and lived in New Jersey, last of Egg Harbor, she was active with quilting, sewing, knitting & crocheting. Collection inherited by donor when her mother passed away.
Some tarnish overall. Large dent in one cabochon and small dent in the other.
Object ID
G.05.15.19
Notes
See another example of this ring found on internet in this file. Iguala is a town near the renowned silvermaking town of Taxco (near the west coast of Mexico) where William Spratling, in the 1930s, famously reinstituted the silver industry and craftsmanship that had died centuries before.
Credit
Gift of Susan Garofola in memory of Lillian Kiker (mother), Heritage Center Collection
Tatting hook of bone handle shaft of iron hook set into smaller end.
Tool has handle of elongated teardrop shape, somewhat flattened in cross-section. Wire-like shaft with rounded hook on tip is set into handle. Shaft is thicker than hooked end.
Provenance
Collected by Lillian Hollings Kiker, born to Scottish Americans who lived in New Jersey. Born (1912) and lived in New Jersey, last of Egg Harbor, she was active with quilting, sewing, knitting & crocheting. Collection inherited by donor when her mother passed away.
Set of tatting tools, nickel silver plated steel, has four pieces. Each piece has in common the shaped and decorated portions, the handles of the three tools and the needle case body. This feature is a flattened octagonal shape in cross-section, with successive divots ground out with a round grinding wheel. Handles and case all taper along their length.
A. Needle case is 2.75" long and .375" wide. At the heavier end of case is a fitted cap that slides onto a smaller male extension protruding from main body. Seam visible along sides where both halves of case have been joined.
B. Hook on handle is 4" long and .25" wide. Tapers from handle end down to where shaft is attached. Shaft has ball-and-ring at handle, a slight swell along length and a minute hook at tip.
C. Awl is 3.625" long and .25" wide. Same handle as above. Shaft is similar in shape except heavier and shorter and has a sharp tip.
D. Threading tool(?) is 3" long and .5" long. Same handle as above. Shaft is shorter and has a large open loop in a teardrop shape.
Provenance
Collected by Lillian Hollings Kiker, born to Scottish Americans who lived in New Jersey. Born (1912) and lived in New Jersey, last of Egg Harbor, she was active with quilting, sewing, knitting & crocheting. Collection inherited by donor when her mother passed away.
Flat shaped tool is constructed of two sheet brass sides riveted together at the handle end, allowing a flat triangular iron blade that is sandwiched between to slide out at the other end for cutting. Blade slides via a small riveted guide that slides along a slot in the brass sides. Cutter's brass sides have a fleur-de-lis-shaped handle and scalloped sides and each slot has a measuriing scale numbered from one to ten.
Inscription: The sliding guide on both sides of the slot reads "D.M.CO. / PAT SEPT. 3, 72 / BPT.CONN."
Provenance
Collected by Lillian Hollings Kiker, born to Scottish Americans who lived in New Jersey. Born (1912) and lived in New Jersey, last of Egg Harbor, she was active with quilting, sewing, knitting & crocheting. Collection inherited by donor when her mother passed away.
Set of 3 steel tatting hooks, no handles. All are similar with round, tapering shanks that terminate in tiny hooks of differing sizes. Theaded at other end for fitting into a handle, now missing. Double ring turnings adjacent to threads.
Provenance
Collected by Lillian Hollings Kiker, born to Scottish Americans who lived in New Jersey. Born (1912) and lived in New Jersey, last of Egg Harbor, she was active with quilting, sewing, knitting & crocheting. Collection inherited by donor when her mother passed away.
Cast-iron toy tri-motor Fokker aquaplane, painted yellow. Made of multiple castings fitted and securred with screws. Three wire spring cables are fitted to pulleys under plane, allowing the 4 rubber wheels to turn the 3 propellers and activate a noisemaker. Raised letters atop wings spell "FRIENDSHIP". "NX4202" is on tail and "Fokker" is on left side of fuselage. All letters painted blue. Inside hollow fuselage is "HUBLEY." Gold seal on left end of wing reads "It's a Hubley Toy". Profile of Earhart is cast into one of the two rear windows on left side.
The Friendship was flown across the Atlantic from Newfoundland to Wales, on June 17, 1928, with Amelia Earhart aboard. She was only a passenger, but this event won her immense fame, including a ticker tape parade in New York City, and started her career as a major celebrity. (see Notes on why this plane was made.)
Provenance
Plane was given to donor by his friend Charlie Reiger (sp?).
Moderate overal loss of paint; rust on exposed metal; cracking rubber on wheels.
Object ID
G.88.9
Notes
Hubley Mfg. Co. was commissioned by Pittsburgh industrialist Arthur E. Braun (1876-1976) to make 22 yellow aquaplanes modeled on Earhart's Friendship. Earhart signed each one and Braun gave the planes out as gifts at a reception in honor of Earhart, held at his own residence in Pittsburgh in June of 1929. This plane is unsigned, suggesting perhaps that this example may have been a factory extra.
In 1932, Earhart flew solo across the Atlantic, again achieving acclaim as the 2nd person and 1st woman to do so. She received the Distinguished Flying Cross from Congress, the gold medal of the National Geographic Society and the Cross of the Legion of Honor from France.
Place of Origin
Lancaster
Credit
Gift of Samuel S. Snyder, Heritage Center Collection
